|
|
Make Soap in Your Crock-Pot
by Judi Cox
Making soap in a crock pot is an easy way to use the "hot process"
method.
These instructions outline my steps for making crock pot soap and assume
you are familiar with the soap making process.
Start with a good recipe. I prefer recipes that have a higher amount of
liquid oil to solids. One of my favorite recipes is very simple: 60%
Olive Oil, 20% Palm Kernel Oil, 20% Palm Oil. Run it through a lye
calculator to determine the amount of lye and [distilled] water needed.
I don't discount my water when making hot process.
I use a 6 1/2 quart crock pot. A 4 pound batch of soaps fits perfectly.
It fills the crock pot about half full - giving room in the case of it
bubbling up, but not too little an amount that it could burn.
First, measure water and set aside.
Then measure the lye into a separate container. Slowly pour the lye into
the pitcher of cold water. Stir until dissolved. Set aside in a safe
place.
Once I have my lye mixture set aside, I measure my solid oils. These can
be put into the crock pot to be melted. But, it takes longer this way,
so I generally put them into the microwave for a couple minutes until
melted and then pour into the crock-pot.
At this point, my crock pot is on low.
I recommend using a good rubber spatula to scrape the bowl - no sense
leaving any good oils behind.
Next, I measure my olive oil - and/or any other liquid oils I happen to
be using - and pour this into the crock-pot.
Get out your handy-dandy stick blender and using low speed, slowly pour
the lye mixture into the melted oils. Gently move the stick blender
around, up, down, around, ensuring a nice even blend. If you don't have
a stick blender, a stainless steel wire whisk works great too - just
requires a little more arm power.
Once it has reached 'trace', I put the lid on the crock-pot and turn the
heat setting up to high. However, the first few times I made crock pot
soap, I left it on low until I was confident in how it worked (both the
soap AND my crock-pot).
Now, I ready my mold, measure out any fragrance oils or essential oils
and any additives I plan to use.
After about 15 or 20 minutes, I take the lid off and, using a potato
masher, mash the soap around. It has a look of a Vaseline texture;
glossy, slick. It will have a waxy feel if you rub a piece of it between
gloved fingers.
Add your additives, colorants, herbs, etc and mix well using the potato
masher. Once that is blended fairly well, add your fragrance and mix
again.
It is done! At this point, it's really soap. It only needs to be put
into your mold. I do this in large spoonfuls, pounding my mold on the
counter every few scoops to ensure it packs into the mold tightly. Once
I have it all in the mold, I put a baggie on my hand and flatten the top
- making sure to "squish" it into the corners really well.
Now is a good time to wash all the dishes. And you don't even need to
add any soap! You should see some lovely lather from the soap you've
just made.
I let this sit over-night. The next morning, I unmold and slice into
bars to air out for a week or so. Once each bar has had time to harden,
I bevel each one and it's ready for use, or sale.
My favorite crock pot soap recipe:
Rosemary Mint Handmade Soap
4 pounds
- 38 ounces olive oil (59.38%)
- 14.4 ounces palm kernel oil (22.5%)
- 11.6 ounces palm oil (18.13%)
- 8.7 ounces sodium hydroxide (5% discount)
- 17.5 ounces distilled water
- 3 ounces rosemary mint blend essential oils
- 2 teabags of Organic Peppermint tea
Disclaimer: Sodium Hydroxide is highly caustic and should be handled
carefully and knowledgeably. It is the soapmaker’s responsibility to
research safety procedures for soap making.
About the author
Judi Cox is a wife and mother of 4 children. Her hobbies include making
handmade soap from scratch, gardening, crafts, web design and
maintaining Mom’s Little Garden, an online resource for pregnant
mothers, as well as her personal website, Momma Muse.
|
|
